1. <dd id="d5hye"><track id="d5hye"><dl id="d5hye"></dl></track></dd><legend id="d5hye"><center id="d5hye"><video id="d5hye"></video></center></legend>

          1. <rp id="d5hye"><ruby id="d5hye"></ruby></rp>

            <rp id="d5hye"></rp>

                丁基膠打膠機的保養要注意什么?

                發布時間:2022/01/06    發布人:

                1.潤滑兩個電動機。丁基膠打膠機的主電動機和輔助電動機的入口均裝有潤滑器。
                1. Lubricate both motors. Lubricators are installed at the inlet of main motor and auxiliary motor of butyl glue applicator.
                當機油低于低端刻線時,應將機油杯取下并重新加注10號機油。 如果沒有注油器,則在滴油或電動機嚴重缺油時,可以拆下主電動機進氣管和電動機之間的帶電連接,并應使用油槍補充油,并使用輔助電動機 可以旋開端蓋螺母以加油。
                When the oil is lower than the low-end notch, remove the oil cup and refill No. 10 oil. If there is no oiler, in case of oil dripping or serious oil shortage of the motor, the live connection between the air inlet pipe of the main motor and the motor can be removed, and the oil gun shall be used to replenish the oil, and the end cover nut can be loosened for refueling with the auxiliary motor.
                2.丁基膠打膠機使用一段時間后,主泵,輔助泵和比例泵會從內部泄漏膠水,并流入油杯。 您可以清潔膠水并添加油。 用十字螺絲刀固定住主泵,將兩個泵油碗的下端的圓孔順時針擰緊。 配套的油杯可用扳手擰緊。
                2. After the butyl glue applicator is used for a period of time, the main pump, auxiliary pump and proportional pump will leak glue from the inside and flow into the oil cup. You can clean the glue and add oil. Fix the main pump with a cross screwdriver and tighten the round holes at the lower ends of the two pump oil bowls clockwise. The matched oil cup can be tightened with a wrench.

                雙組份打膠機
                3.用油槍將安全閥注滿安全閥的小孔,以防生銹。
                3. Fill the small hole of the safety valve with an oil gun to prevent rust.
                4. Y型過濾器位于輔助泵的出口。 清潔時,擰開端蓋,將其浸入煤油中,然后用牙刷清潔。 安裝時,將網罩放到端蓋中并擰到底,然后用扳手擰緊。 用一套膠水清洗一次,如果沒有雜質,用兩套膠水清洗,控制靈活。
                4. The Y-type filter is located at the outlet of the auxiliary pump. When cleaning, unscrew the end cap, immerse it in kerosene, and then clean it with a toothbrush. During installation, put the net cover into the end cover and screw it to the end, and then tighten it with a wrench. Clean once with one set of glue. If there are no impurities, clean with two sets of glue for flexible control.
                5.大型過濾器的位置在高壓儀表B臺的右下角,擰下回油閥下方的軟管,擰下過濾器,取出網和芯,彈簧,取出,用刷子清洗, 并用凸塊上的芯覆蓋彈簧的小孔。 向后旋轉,然后將其擰緊在丁基膠打膠機上。
                5. The large filter is located at the lower right corner of the high-pressure instrument B. unscrew the hose under the oil return valve, unscrew the filter, take out the net and core, take out the spring, clean it with a brush, and cover the small hole of the spring with the core on the boss. Rotate it backward and tighten it on the butyl glue applicator.
                3-5組洗一次。 如果沒有雜質,則可以靈活控制。
                Wash once for 3-5 groups. If there are no impurities, it can be flexibly controlled.
                以上就是雙組份打膠機給大家的精彩內容,更多的精彩內容請點擊:http://www.ab789789.com我們后續會有更多的精彩內容等您查看.
                These are the highlights of the two-component gluing machine. For more highlights, please click: http://www.ab789789.com We will have more wonderful content for you to check later

                国产精品国产亚洲精品看不卡
                1. <dd id="d5hye"><track id="d5hye"><dl id="d5hye"></dl></track></dd><legend id="d5hye"><center id="d5hye"><video id="d5hye"></video></center></legend>

                      1. <rp id="d5hye"><ruby id="d5hye"></ruby></rp>

                        <rp id="d5hye"></rp>